🛒 Buy the RG52 MINI Cooling Fan Upgrade Kit – Shop Now

RG52 MINI Cooling Fan Installation Guide

Want to upgrade your RG52 MINI with active cooling? This step-by-step installation guide will walk you through everything you need to know, from connecting the cooling fan to installing the thermal pad and securing the fan module.

Follow these seven simple steps to install your RG52 MINI Cooling Fan Upgrade Kit safely and correctly.

Compatibility Notice: This cooling fan upgrade kit is designed exclusively for RG52 MINI consoles with the AISLPC logo on the back. Please check your device before installation. Models without the AISLPC logo are not supported.

What's in the Box?

Before starting, make sure you have all the included accessories:

1 × Cooling Fan & Heatsink Module
1 × Thermal Silicone Pad
1 × Phillips Screwdriver
1 × L-Shaped Hex Key
5 × Mounting Screws (4 for Installation + 1 Spare)

Step 1: Power Off Your RG52 MINI

Before installation, make sure your RG52 MINI is completely powered off.

Disconnect the charging cable and any connected accessories.

Important: Never connect or disconnect internal components while the device is powered on.

Step 2: Remove the Fan Cover

Locate the fan cover on the back of your RG52 MINI.

Use the included L-shaped hex key to carefully remove the four screws securing the cover.

Gently lift off the cover and keep the screws in a safe place. You will need them during reassembly.

Tip: Place the screws in a small container to prevent losing them.

Step 3: Connect the 4-Pin Fan Cable

Locate the dedicated fan connector inside your RG52 MINI.

Carefully align the fan's 4-pin plug with the corresponding connector on the device.

Gently press the plug into place until it is securely connected.

Important:

Make sure all four pins are correctly aligned.
Check the connector orientation before inserting the plug.
Never force the connector into place.
If necessary, use a screwdriver to gently press the plastic housing of the plug. Avoid pressing directly on the pins.

An incorrect connection may prevent the cooling fan from working properly.

Step 4: Test the Cooling Fan

Before securing the fan module, briefly power on your RG52 MINI to verify the connection.

During startup, the cooling fan automatically performs a short self-test.

What to expect:

The fan spins for approximately 1 second.
The fan then stops automatically.
This brief startup rotation is normal.

If the fan does not spin:

Turn off the device completely.
Check that the 4-pin connector is correctly aligned.
Make sure the plug is firmly seated.
Power on the device again to repeat the test.

Important: Once the fan test is complete, turn off your RG52 MINI before proceeding to the next step. Do not touch exposed internal components while the device is powered on.

Step 5: Apply the Thermal Pad

Take the included thermal silicone pad and position it on the designated contact area on the back of the cooling fan module.

Important: Before installation, carefully remove the transparent protective film from the thermal pad.

If protective films are present on both sides, remove both before completing the installation.

Make sure the thermal pad is positioned correctly and remains clean.

Tip: Avoid touching the exposed thermal pad surface unnecessarily.

Step 6: Secure the Cooling Fan Module

Carefully position the cooling fan module over the designated mounting area.

Align the four mounting holes with the corresponding screw holes on the device.

Using the included Phillips screwdriver, secure the fan module with four mounting screws.

Important:

Route the fan cable neatly into the corner space.
Make sure the cable does not touch the fan blades.
Avoid pinching the cable between the fan module and the device.
Tighten all four screws evenly without overtightening.

Make sure the fan module is securely installed before continuing.

Step 7: Reinstall the Fan Cover

Place the original fan cover back onto your RG52 MINI.

Use the four screws removed in Step 2 to secure the cover.

Check that the cover sits properly and that no cables are pinched or exposed.

Congratulations! Your RG52 MINI Cooling Fan Upgrade Kit is now installed!

You can now power on your device and enjoy your upgraded active cooling system.

Frequently Asked Questions (FAQ)

Why does my RG52 MINI fan spin for only one second during startup?

This is normal. The cooling fan performs a brief self-test when your RG52 MINI powers on. The fan spins for approximately one second and then stops. This does not indicate an installation problem.

What should I do if the cooling fan does not spin?

First, power off your RG52 MINI. Check that the 4-pin fan connector is facing the correct direction and is securely connected. Then restart the device to repeat the startup test.

Is the cooling fan compatible with every RG52 MINI?

No. This cooling fan upgrade kit is compatible only with RG52 MINI consoles featuring the AISLPC logo on the back. Models without the AISLPC logo are not supported.

Do I need to remove the transparent film from the thermal pad?

Yes. The transparent protective film must be removed before installation. If both sides have protective films, remove both to allow proper thermal contact.

What tools do I need to install the cooling fan?

The upgrade kit includes the tools needed for installation: one L-shaped hex key, one Phillips screwdriver, and five mounting screws, including one spare.